Вставляем ZTE MF626 загорается оранжевый индикатор usb 5-8 new high sp

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Вставляем ZTE MF626:
загорается оранжевый индикатор
usb 5-8: new high speed USB device using ehci_hcd and address 3
usb 5-8: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
через небольшой промежуток -- синий индикатор:
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access ZTE MMC Storage 322 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdb] Attached SCSI removable disk
Делаю modprobe usbserial vendor=0x19d2 product=0x0031
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbserial_generic 5-8:1.0: Generic device with no bulk out, not allowed.
usbserial_generic: probe of 5-8:1.0 failed with error -5
usbserial_generic 5-8:1.3: generic converter detected
usb 5-8: generic converter now attached to ttyUSB0
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
Запускаю sudo mf626-helper -v 005 008
I: Trying to open 005:008
I: Found ZTE626 modem
проходит 9 минут...
I: Modem 005:008 has been disconnected. Terminating.
в dmesg:
usb 5-8: reset high speed USB device using ehci_hcd and address 3
usb 5-8: device descriptor read/64, error -110
usb 5-8: device descriptor read/64, error -110
usb 5-8: reset high speed USB device using ehci_hcd and address 3
usb 5-8: device descriptor read/64, error -110
usb 5-8: device descriptor read/64, error -110
usb 5-8: reset high speed USB device using ehci_hcd and address 3
usb 5-8: device not accepting address 3, error -110
usb 5-8: reset high speed USB device using ehci_hcd and address 3
usb 5-8: device not accepting address 3, error -110
usb 5-8: USB disconnect, address 3
scsi 2:0:0:0: Device offlined - not ready after error recovery
generic ttyUSB0: generic converter now disconnected from ttyUSB0
usbserial_generic 5-8:1.3: device disconnected
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: [sdb] READ CAPACITY failed
scsi 2:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
scsi 2:0:0:0: [sdb] Sense not available.
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: [sdb] Write Protect is off
scsi 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 2:0:0:0: [sdb] Assuming drive cache: write through
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: [sdb] READ CAPACITY failed
scsi 2:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
scsi 2:0:0:0: [sdb] Sense not available.
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: [sdb] Write Protect is off
scsi 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 2:0:0:0: [sdb] Assuming drive cache: write through
scsi 2:0:0:0: rejecting I/O to dead device
usb 5-8: new high speed USB device using ehci_hcd and address 4
usb 5-8: device descriptor read/64, error -110
usb 5-8: device descriptor read/64, error -110
usb 5-8: new high speed USB device using ehci_hcd and address 5
usb 5-8: device descriptor read/64, error -110
usb 5-8: device descriptor read/64, error -110
usb 5-8: new high speed USB device using ehci_hcd and address 6
usb 5-8: device not accepting address 6, error -110
usb 5-8: new high speed USB device using ehci_hcd and address 7
usb 5-8: device not accepting address 7, error -110
lsusb не показывает подключенное устройство, синий индикатор горит