--- dmesg.txt 2009-07-14 11:51:54 +0400
+++ dmesg.1.txt 2009-07-14 11:52:14 +0400
@@ -1,5 +1,5 @@
-Bootdata ok (command line is auto BOOT_IMAGE=2618-ovz-smp-23M402 ro root=802 panic=30)
-Linux version 2.6.18-ovz-smp-alt23.M40.2 (builder@apiary.rio.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Wed Jun 11 11:49:30 MSD 2008
+Bootdata ok (command line is auto BOOT_IMAGE=2618-ovz-smp-26M402 ro root=802 panic=30)
+Linux version 2.6.18-ovz-smp-alt26.M40.2 (builder@apiary.int.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Thu Nov 13 21:39:31 MSK 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
@@ -82,19 +82,19 @@
Nosave address range: 00000000ffc00000 - 0000000100000000
Allocating PCI resources starting at f1000000 (gap: f0000000:ec00000)
Built 1 zonelists. Total pages: 2060445
-Kernel command line: auto BOOT_IMAGE=2618-ovz-smp-23M402 ro root=802 panic=30
+Kernel command line: auto BOOT_IMAGE=2618-ovz-smp-26M402 ro root=802 panic=30
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
-time.c: Detected 3000.180 MHz processor.
+time.c: Detected 3000.178 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0xa666000 - 0xe666000
-Memory: 8163120k/9043968k available (1919k kernel code, 224508k reserved, 1265k data, 220k init)
-Calibrating delay using timer specific routine.. 6005.82 BogoMIPS (lpj=12011658)
+Memory: 8163120k/9043968k available (1922k kernel code, 224508k reserved, 1261k data, 220k init)
+Calibrating delay using timer specific routine.. 6005.69 BogoMIPS (lpj=12011385)
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
@@ -109,11 +109,11 @@
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
Using local APIC timer interrupts.
-result 12500686
+result 12500676
Detected 12.500 MHz APIC timer.
Booting processor 1/4 APIC 0x6
Initializing CPU#1
-Calibrating delay using timer specific routine.. 6001.26 BogoMIPS (lpj=12002537)
+Calibrating delay using timer specific routine.. 5663.92 BogoMIPS (lpj=11327853)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 3
@@ -122,7 +122,7 @@
Intel(R) Xeon(TM) CPU 3.00GHz stepping 0a
Booting processor 2/4 APIC 0x1
Initializing CPU#2
-Calibrating delay using timer specific routine.. 6000.73 BogoMIPS (lpj=12001476)
+Calibrating delay using timer specific routine.. 6000.84 BogoMIPS (lpj=12001689)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
@@ -131,7 +131,7 @@
Intel(R) Xeon(TM) CPU 3.00GHz stepping 0a
Booting processor 3/4 APIC 0x7
Initializing CPU#3
-Calibrating delay using timer specific routine.. 6001.01 BogoMIPS (lpj=12002037)
+Calibrating delay using timer specific routine.. 6000.23 BogoMIPS (lpj=12000469)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 3
@@ -140,7 +140,7 @@
Intel(R) Xeon(TM) CPU 3.00GHz stepping 0a
Brought up 4 CPUs
testing NMI watchdog ... OK.
-migration_cost=32,3707
+migration_cost=4,1312
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
@@ -252,7 +252,7 @@
TCP reno registered
Simple Boot Flag at 0x40 set to 0x1
audit: initializing netlink socket (disabled)
-audit(1247572259.320:1): initialized
+audit(1247571575.144:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
@@ -374,76 +374,70 @@
ARECA RAID ADAPTER1: FIRMWARE VERSION V1.44 2008-2-1
scsi1 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
Driver Version 1.20.00.13
+ Vendor: Areca Model: RAID controller Rev: R001
+ Type: Processor ANSI SCSI revision: 00
+GSI 19 sharing vector 0xC1 and IRQ 19
+ACPI: PCI Interrupt 0000:0a:0e.0[A] -> GSI 74 (level, low) -> IRQ 193
+ARECA RAID ADAPTER2: FIRMWARE VERSION V1.44 2008-2-1
+scsi2 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
+ Driver Version 1.20.00.13
Vendor: Areca Model: ARC-1160-VOL#00 Rev: R001
Type: Direct-Access ANSI SCSI revision: 05
sdf : very big device. try to use READ CAPACITY(16).
-SCSI device sdf: 7814096896 512-byte hdwr sectors (4000818 MB)
+SCSI device sdf: 20507805696 512-byte hdwr sectors (10499997 MB)
sdf: Write Protect is off
sdf: Mode Sense: cb 00 00 08
SCSI device sdf: drive cache: write back
sdf : very big device. try to use READ CAPACITY(16).
-SCSI device sdf: 7814096896 512-byte hdwr sectors (4000818 MB)
+SCSI device sdf: 20507805696 512-byte hdwr sectors (10499997 MB)
sdf: Write Protect is off
sdf: Mode Sense: cb 00 00 08
SCSI device sdf: drive cache: write back
sdf: unknown partition table
-sd 1:0:0:0: Attached scsi disk sdf
- Vendor: Areca Model: SIB2 Rev: R001
- Type: Direct-Access ANSI SCSI revision: 05
-sdg : very big device. try to use READ CAPACITY(16).
-SCSI device sdg: 11721145344 512-byte hdwr sectors (6001226 MB)
-sdg: Write Protect is off
-sdg: Mode Sense: cb 00 00 08
-SCSI device sdg: drive cache: write back
-sdg : very big device. try to use READ CAPACITY(16).
-SCSI device sdg: 11721145344 512-byte hdwr sectors (6001226 MB)
-sdg: Write Protect is off
-sdg: Mode Sense: cb 00 00 08
-SCSI device sdg: drive cache: write back
- sdg: unknown partition table
-sd 1:0:0:1: Attached scsi disk sdg
- Vendor: Areca Model: RAID controller Rev: R001
- Type: Processor ANSI SCSI revision: 00
-GSI 19 sharing vector 0xC1 and IRQ 19
-ACPI: PCI Interrupt 0000:0a:0e.0[A] -> GSI 74 (level, low) -> IRQ 193
-ARECA RAID ADAPTER2: FIRMWARE VERSION V1.44 2008-2-1
-scsi2 : Areca SATA Host Adapter RAID Controller( RAID6 capable)
- Driver Version 1.20.00.13
- Vendor: Areca Model: ARC-1160-VOL#00 Rev: R001
- Type: Direct-Access ANSI SCSI revision: 05
-sdh : very big device. try to use READ CAPACITY(16).
-SCSI device sdh: 20507805696 512-byte hdwr sectors (10499997 MB)
-sdh: Write Protect is off
-sdh: Mode Sense: cb 00 00 08
-SCSI device sdh: drive cache: write back
-sdh : very big device. try to use READ CAPACITY(16).
-SCSI device sdh: 20507805696 512-byte hdwr sectors (10499997 MB)
-sdh: Write Protect is off
-sdh: Mode Sense: cb 00 00 08
-SCSI device sdh: drive cache: write back
- sdh: unknown partition table
-sd 2:0:0:0: Attached scsi disk sdh
+sd 2:0:0:0: Attached scsi disk sdf
Vendor: Areca Model: RAID controller Rev: R001
Type: Processor ANSI SCSI revision: 00
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12ac
-usbcore: registered new driver usbfs
-usbcore: registered new driver hub
-input: PC Speaker as /class/input/input0
-parport: PnPBIOS parport detected.
-parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:1: Attached scsi generic sg1 type 0
sd 0:0:0:2: Attached scsi generic sg2 type 0
sd 0:0:0:3: Attached scsi generic sg3 type 0
sd 0:0:0:4: Attached scsi generic sg4 type 0
scsi 0:0:16:0: Attached scsi generic sg5 type 3
-sd 1:0:0:0: Attached scsi generic sg6 type 0
-sd 1:0:0:1: Attached scsi generic sg7 type 0
-scsi 1:0:16:0: Attached scsi generic sg8 type 3
-sd 2:0:0:0: Attached scsi generic sg9 type 0
-scsi 2:0:16:0: Attached scsi generic sg10 type 3
+scsi 1:0:16:0: Attached scsi generic sg6 type 3
+sd 2:0:0:0: Attached scsi generic sg7 type 0
+scsi 2:0:16:0: Attached scsi generic sg8 type 3
+Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
+ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
+usbcore: registered new driver usbfs
+usbcore: registered new driver hub
+uhci_hcd: Unknown symbol usb_hcd_pci_suspend
+uhci_hcd: Unknown symbol usb_hcd_resume_root_hub
+uhci_hcd: Unknown symbol usb_hcd_pci_probe
+uhci_hcd: Unknown symbol usb_check_bandwidth
+uhci_hcd: Unknown symbol usb_disabled
+uhci_hcd: Unknown symbol usb_release_bandwidth
+uhci_hcd: Unknown symbol usb_claim_bandwidth
+uhci_hcd: Unknown symbol usb_hcd_pci_resume
+uhci_hcd: Unknown symbol usb_hcd_giveback_urb
+uhci_hcd: Unknown symbol usb_hcd_poll_rh_status
+uhci_hcd: Unknown symbol usb_hcd_pci_remove
+uhci_hcd: Unknown symbol usb_root_hub_lost_power
+input: PC Speaker as /class/input/input0
+uhci_hcd: Unknown symbol usb_hcd_pci_suspend
+uhci_hcd: Unknown symbol usb_hcd_resume_root_hub
+uhci_hcd: Unknown symbol usb_hcd_pci_probe
+uhci_hcd: Unknown symbol usb_check_bandwidth
+uhci_hcd: Unknown symbol usb_disabled
+uhci_hcd: Unknown symbol usb_release_bandwidth
+uhci_hcd: Unknown symbol usb_claim_bandwidth
+uhci_hcd: Unknown symbol usb_hcd_pci_resume
+uhci_hcd: Unknown symbol usb_hcd_giveback_urb
+uhci_hcd: Unknown symbol usb_hcd_poll_rh_status
+uhci_hcd: Unknown symbol usb_hcd_pci_remove
+uhci_hcd: Unknown symbol usb_root_hub_lost_power
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.0 to 64
@@ -453,6 +447,8 @@
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
+Intel(R) PRO/1000 Network Driver - version 7.2.7-k2-NAPI
+Copyright (c) 1999-2006 Intel Corporation.
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.1 to 64
@@ -462,8 +458,6 @@
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
-Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
-ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.2 to 64
@@ -473,8 +467,8 @@
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
-Intel(R) PRO/1000 Network Driver - version 7.2.7-k2-NAPI
-Copyright (c) 1999-2006 Intel Corporation.
+parport: PnPBIOS parport detected.
+parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
@@ -521,12 +515,6 @@
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
-Filesystem "dm-1": Disabling barriers, not supported by the underlying device
-XFS mounting filesystem dm-1
-Ending clean XFS mount for filesystem: dm-1
-Filesystem "dm-0": Disabling barriers, not supported by the underlying device
-XFS mounting filesystem dm-0
-Ending clean XFS mount for filesystem: dm-0
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 312 bytes per conntrack
@@ -549,3 +537,7 @@
netconsole: network logging started
NET: Registered protocol family 17
tun: Universal TUN/TAP device driver, 1.6
+tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
+iSCSI Enterprise Target Software - version 0.4.14
+iotype_init(90) register fileio
+iotype_init(90) register nullio